Trimming Cutter With Down Shear Cutting Angle
HW/Z2/RH
The down shear angle cutting flutes produces a smoother cut than the traditional straight flute bits. Instead of chopping at the wood fibers at a 90ﾟ angle, the shear angle design allows for a smoother shear angle, slicing cut. Use this bit to eliminate tear-out problems from routing end or cross grain on very hard woods.
| A inch |
B inch |
C inch |
D inch |
Bearing | Part No. |
|---|---|---|---|---|---|
| 1/4 | 3/4 | 1/4 | 1-1/4 | 1/4 | 151006A |
| 1/4 | 1 | 1/4 | 1-1/4 | 1/4 | 151007A |
| 3/8 | 1/2 | 1/4 | 1-1/4 | 3/8 | 151009A |
| 3/8 | 1 | 1/4 | 1-1/4 | 1/8 | 151010A |
| 1/2 | 1/2 | 1/4 | 1-1/4 | 1/2 | 151011A |
| 1/2 | 1 | 1/4 | 1-1/4 | 1/2 | 151021A |
| 1/2 | 1-1/4 | 1/4 | 1-1/4 | 1/2 | 151041A |
| 5/8 | 1/2 | 1/4 | 1-1/4 | 5/8 | 151071A |
| 5/8 | 1 | 1/4 | 1-1/4 | 5/8 | 151073A |
| 3/4 | 1/2 | 1/4 | 1-1/4 | 3/4 | 151081A |
| 3/4 | 1 | 1/4 | 1-1/4 | 3/4 | 151083A |
| 1/2 | 1/2 | 1/2 | 1-1/2 | 1/2 | 151411A |
| 1/2 | 1 | 1/2 | 1-1/2 | 1/2 | 151421A |
| 1/2 | 1-3/16 | 1/2 | 1-1/2 | 1/2 | 151431A |
| 1/2 | 1-1/4 | 1/2 | 1-1/2 | 1/2 | 151441A |
| 1/2 | 1-1/2 | 1/2 | 1-1/2 | 1/2 | 151451A |
| 1/2 | 2 | 1/2 | 1-1/2 | 1/2 | 151461A |
| 5/8 | 1/2 | 1/2 | 1-1/2 | 5/8 | 151471A |
| 5/8 | 1 | 1/2 | 1-1/2 | 5/8 | 151473A |
| 5/8 | 1-1/4 | 1/2 | 1-1/2 | 5/8 | 151475A |
| 5/8 | 1-1/2 | 1/2 | 1-1/2 | 5/8 | 151477A |
| 5/8 | 2 | 1/2 | 1-1/2 | 5/8 | 151479A |
| 3/4 | 1/2 | 1/2 | 1-1/2 | 3/4 | 151481A |
| 3/4 | 1 | 1/2 | 1-1/2 | 3/4 | 151483A |
| 3/4 | 1-1/4 | 1/2 | 1-1/2 | 3/4 | 151485A |
| 3/4 | 1-1/2 | 1/2 | 1-1/2 | 3/4 | 151487A |
| 3/4 | 2 | 1/2 | 1-1/2 | 3/4 | 151489A |
| A mm |
B mm |
C=Ø6x32mm Part No. |
C=Ø8x32mm Part No. |
C=Ø12x40mm Part No. |
Bearing No. |
|---|---|---|---|---|---|
| 12.7 | 25.4 | 151621A | 151821A | 151221A | 706051 |
| 19.05 | 25.4 | 151683A | 151883A | 151283A | 706081 |
| 19.05 | 38.1 | 151287A | 706081 | ||
| 19.05 | 50.8 | 151289A | 706081 |